Tweeted twitter.com/#!/StackRaspi/status/378855397144403968
2 link to the spec
source | link

From some links, it seems that the Rev1 has a few "DNC" (Do Not Connect) pins. However, the diagram on eLinux wiki shows some of them as GND, others as powered (3.3V or 5V). There's also a relevant discussion in raspberrypi.org comment archives, which mentions some Rev1 Schematic (where to find it?probably this one, see page 2/5, element PH-26/004 in the center), and seems to suggest that on that schematic these pins were actually already defined for Rev1.

So, what's the real status of those pins on a Rev1 board - are they "Do Not Connect", or are they "you can connect"?

So for example, can I take the "Do Not Connect" GND from pin P1-20 to ground some switch connected to e.g. pin P1-18 (GPIO 24) (obviously, with a resistor)? Or, can I use solely the pins 17 (DNC?/3v3), 19 (MOSI), 20 (DNC?/GND), 21 (MISO), 23 (SCLK) to power and connect some external SPI peripheral?

From some links, it seems that the Rev1 has a few "DNC" (Do Not Connect) pins. However, the diagram on eLinux wiki shows some of them as GND, others as powered (3.3V or 5V). There's also a relevant discussion in raspberrypi.org comment archives, which mentions some Rev1 Schematic (where to find it?), and seems to suggest that on that schematic these pins were actually already defined for Rev1.

So, what's the real status of those pins on a Rev1 board - are they "Do Not Connect", or are they "you can connect"?

So for example, can I take the "Do Not Connect" GND from pin P1-20 to ground some switch connected to e.g. pin P1-18 (GPIO 24) (obviously, with a resistor)? Or, can I use solely the pins 17 (DNC?/3v3), 19 (MOSI), 20 (DNC?/GND), 21 (MISO), 23 (SCLK) to power and connect some external SPI peripheral?

From some links, it seems that the Rev1 has a few "DNC" (Do Not Connect) pins. However, the diagram on eLinux wiki shows some of them as GND, others as powered (3.3V or 5V). There's also a relevant discussion in raspberrypi.org comment archives, which mentions some Rev1 Schematic (probably this one, see page 2/5, element PH-26/004 in the center), and seems to suggest that on that schematic these pins were actually already defined for Rev1.

So, what's the real status of those pins on a Rev1 board - are they "Do Not Connect", or are they "you can connect"?

So for example, can I take the "Do Not Connect" GND from pin P1-20 to ground some switch connected to e.g. pin P1-18 (GPIO 24) (obviously, with a resistor)? Or, can I use solely the pins 17 (DNC?/3v3), 19 (MOSI), 20 (DNC?/GND), 21 (MISO), 23 (SCLK) to power and connect some external SPI peripheral?

1
source | link

Status of DNC (Do Not Connect) GPIO pins in Rev1?

From some links, it seems that the Rev1 has a few "DNC" (Do Not Connect) pins. However, the diagram on eLinux wiki shows some of them as GND, others as powered (3.3V or 5V). There's also a relevant discussion in raspberrypi.org comment archives, which mentions some Rev1 Schematic (where to find it?), and seems to suggest that on that schematic these pins were actually already defined for Rev1.

So, what's the real status of those pins on a Rev1 board - are they "Do Not Connect", or are they "you can connect"?

So for example, can I take the "Do Not Connect" GND from pin P1-20 to ground some switch connected to e.g. pin P1-18 (GPIO 24) (obviously, with a resistor)? Or, can I use solely the pins 17 (DNC?/3v3), 19 (MOSI), 20 (DNC?/GND), 21 (MISO), 23 (SCLK) to power and connect some external SPI peripheral?