Return to Question

i've bought a nano wifi adapter at modmypi.com (this one: https://www.modmypi.com/raspberry-pi-accessories/wireless-USB%20-1N-nano-adaptor-802.11N-(WiFi-dongle))

It works, i checked it in a raspbmc configuration (i used raspbmc to configure it there)

Now i'm back at my wheezy distro, and i can't get it to work.

When i do a ifconfig it's there (see below).

The help page on modmypi.com had a script, but when i run that, i get this exception:"Looks like you're using the new 2012-09-18-wheezy-raspbian image. Sorry but the script will not currently set up the wifi on this image. You need to start the GUI using command startx and set it up using WiFi Config. The script will now terminate. Press any key to continue ..."

So now i am in the GUI, and started nm-connection-editor, but it doesn't seem to get an ipaddress.

And now i don't know what to do :-)

This is the ifconfig:

iwconfig wlan0

/etc/wpa_supplicant/wpa_supplicant.conf

executing wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf gives this:

I've bought a nano wifi adapter at modmypi.com (this one).

It works, I checked it in a raspbmc configuration (I used raspbmc to configure it there).

Now I'm back at my wheezy distro, and I can't get it to work.

When I do a ifconfig it's there (see below).

The help page on modmypi.com had a script, but when I run that, I get this exception:  "Looks like you're using the new 2012-09-18-wheezy-raspbian image. Sorry but the script will not currently set up the wifi on this image. You need to start the GUI using command startx and set it up using WiFi Config. The script will now terminate. Press any key to continue ..."

So now I am in the GUI, and started nm-connection-editor, but it doesn't seem to get an ipaddress.

And now I don't know what to do.

This is the ifconfig:

iwconfig wlan0:

/etc/wpa_supplicant/wpa_supplicant.conf:

Executing wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf gives this:

/etc/wpa_supplicant/wpa_supplicant.conf

ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
update_config=1


network={
        ssid="Nerd"
        psk="SECRET"
        proto=RSN
        key_mgmt=WPA-PSK
        pairwise=CCMP TKIP
        group=CCMP TKIP
}

executing wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf gives this:

wlan0: Trying to associate with 2a:65:11:f2:ce:97 (SSID='Nerd' freq=2412 MHz)
wlan0: Association request to the driver failed
wlan0: Associated with 2a:65:11:f2:ce:97
wlan0: WPA: Key negotiation completed with 2a:65:11:f2:ce:97 [PTK=CCMP GTK=TKIP]
wlan0: CTRL-EVENT-CONNECTED - Connection to 2a:65:11:f2:ce:97 completed (auth) [id=0 id_str=]
wlan0: CTRL-EVENT-DISCONNECTED bssid=2a:65:11:f2:ce:97 reason=0
wlan0: Trying to associate with 90:00:4e:87:c8:cf (SSID='Nerd' freq=2412 MHz)
wlan0: Association request to the driver failed
wlan0: Associated with 00:00:00:00:00:00
wlan0: CTRL-EVENT-TERMINATING - signal 2 received
wlan0: Trying to associate with 90:00:4e:87:c8:cf (SSID='Nerd' freq=2412 MHz)
wlan0: Association request to the driver failed

iwconfig wlan0

wlan0     unassociated  Nickname:"<WIFI@REALTEK>"
          Mode:Managed  Frequency=2.412 GHz  Access Point: Not-Associated   
          Sensitivity:0/0  
          Retry:off   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0