Using this microphone I have some severe noise in the background. The more peripherals I plug in (camera, gertboard, wi-fi adapter) the worse the noise becomes. We've tried several different power supplies, however the problem still remains. The microphone seems to pick up some switching noise from the pi itself and from the peripherals connected to it. The most significant frequency one can hear sounds to be about 1 Khz.

The noise is not present if one plugs in the microphone into any other computer. So the problem clearly lies with the raspberry pi itself. Do you have any suggestions as to what to do about this problem?

I am using a Raspberry Pi Model B with old linear regulators. Perhaps the problem could be fixed by using a USB hub with an external power supply?

(EDIT: So, I took a new sample from a video today and one can hear a "click" sound every second which I find wouldn't sound too much alike ground loop noise. Anyway here's a image of the frequency analysis: enter image description here

Here is the spectrum.txt exported from audacity.)

  • Maybe this is a stupid question but have you just tried a USB extension cable to distance the mic from the Pi?
    – rob
    Commented Aug 4, 2015 at 9:00
  • @rob yes, I tried doing that. But it still generates the exact same noise.
    – Linus
    Commented Aug 4, 2015 at 11:05
  • @rob Also, the volume is always the same, I believe the amplitude is around 0.2 on a scale from 0 to 1. It's a constant tone which is very alike to a 1 Khz sawtooth/square tone.
    – Linus
    Commented Aug 4, 2015 at 11:14
  • I have about the same spectrum with about the same mic plug.... Commented Nov 21, 2020 at 16:02

2 Answers 2


In the audio world when you have questionable analog audio capture, the first thing you chase down is your power supply and the cleanliness of the power it provides. A bad power supply will muck up the sound of even the best ADC's.

The first thing I would try in this is to introduce a bypass capacitor, a small one (47uF@16v or so electrolytic should be fine and are readily available) at first, to the supply side of the RpiB. This is the simplest and cheapest way to first see if the noise is really coming from the DC supply.

You would hook the Capacitor up in parallel with the RpiB board so that all positive leads are tied together, and respectively all negative leads are tied.

Doing this will either require you to have a small breakout board with a female microUSB input and USB A header after the capacitor (also easiest to swap out capacitors), or directly soldering the capacitor to the backside of the RpiB board to the traces closest to the microUSB power connector.

If this helps the issue but still doesn't get it down a magnitude, I would suggest localizing the bypass capacitor closer to the USB jack of the microphone- this should help you by attempting to sink some of the high frequency noise on the DC lines right before it enters the power traces for the ADC inside. For best results a full isolation of the power supply, one that is completely separate from the Rpi itself and properly smoothed/filtered, would be most ideal, but also comes at both a physical and monetary cost to implement and becomes a question of just how important is it to you to eliminate a 1KHz noise and lower your noise floor.

I can't say I've had problems like this on my Rpi2B since it's been on the step-down isolation power supply I built for it, but I do remember the analog audio had a 1KHz or so sawtooth wave (and a horrible noise floor) to its output before switching to my own supply from a standard 5V2A phone charger.

To give more of a background, to just how expensive something can get for the best quality audio power supply, I've seen an "on-line" double conversion power supply supplying power to a MSB DAC board with a 140 femtosecond clock mounted on it. It was part of a system called "The Beast" http://www.msbtech.com/products/serverComp.php?Page=dac5home


It might come from the USB-power-supply, it must either be smoothed, or be supplied externally. I'd use an USB-extender, pull out the power supply and connect that not to the pi, but to an own - external power supply.

  • On my side about the same spectrum is observed powering the PI with an external battery... Commented Nov 22, 2020 at 10:40

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.