i have set up hostapd and dnsmasq and ran into some issues. at first the issue was that hostapd didn't recognized the driver. after i deleted that line it did start up. then dnsmasq told me that there was an invalid option in the /etc/dnsmasq.conf which was the "listen-address" option. after deleting that line dnsmasq started up aswell and both services are running. but the problem i have now is that i don't get any signal to my devices. it should normally show the ssid "WiPi-Repeater" but i don't get any signal. i am using:
- Raspberry Pi 3 Model B
- TP-Link Archer T2U wifi dongle
- 2019-04-08-raspbian-stretch-full image.
I hope you guys can help me because i haven't found anything according to my problem yet.
Here is the hostapd.conf:
interface=wlan1 hw_mode=g channel=6 ieee80211n=1 wmm_enabled=1 ht_capab=[HT40][SHORT-GI-20][DSSS_CCK-40] macaddr_acl=0 ignore_broadcast_ssid=0 auth_algs=1 wpa=2 wpa_key_mgmt=WPA-PSK rsn_pairwise=CCMP ssid=WiPi-Repeater wpa_passphrase=mypassword
and here the dnsmasq.conf:
interface=wlan1 bind-interfaces server=184.108.40.206 domain-needed bogus-priv dhcp-range=192.168.178.50,192.168.178.150,12h
if i use
sudo systemctl is-active dnsmasq and
sudo systemctl is-active hostapd both are marked as
lsusb command i get:
Bus 001 Device 004: ID 148f:761a Ralink Technology, Corp. Bus 001 Device 006: ID 1a2c:0e24 China Resource Semico Co., Ltd Bus 001 Device 005: ID 145f:01de Trust Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast Ethernet Adapter Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp. SMC9514 Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Module Size Used by fuse 110592 3 rfcomm 49152 4 bnep 20480 2 hci_uart 36864 1 btbcm 16384 1 hci_uart serdev 20480 1 hci_uart bluetooth 368640 29 hci_uart,bnep,btbcm,rfcomm ecdh_generic 28672 1 bluetooth ipt_MASQUERADE 16384 1 nf_nat_masquerade_ipv4 16384 1 ipt_MASQUERADE iptable_nat 16384 1 nf_nat_ipv4 16384 1 iptable_nat nf_nat 28672 2 nf_nat_masquerade_ipv4,nf_nat_ipv4 nf_conntrack_ipv4 16384 3 nf_defrag_ipv4 16384 1 nf_conntrack_ipv4 xt_conntrack 16384 1 nf_conntrack 126976 6 nf_conntrack_ipv4,ipt_MASQUERADE,nf_nat_masquerade_ipv4,xt_conntrack,nf_nat_ipv4,nf_nat iptable_filter 16384 1 evdev 24576 8 joydev 20480 0 mt7610u 688128 1 brcmfmac 307200 0 brcmutil 16384 1 brcmfmac snd_bcm2835 32768 1 snd_pcm 98304 1 snd_bcm2835 cfg80211 573440 2 mt7610u,brcmfmac snd_timer 32768 1 snd_pcm rfkill 28672 8 bluetooth,cfg80211 snd 69632 5 snd_timer,snd_bcm2835,snd_pcm fixed 16384 0 uio_pdrv_genirq 16384 0 uio 20480 1 uio_pdrv_genirq i2c_dev 16384 0 ip_tables 24576 2 iptable_filter,iptable_nat x_tables 32768 4 ip_tables,iptable_filter,ipt_MASQUERADE,xt_conntrack ipv6 425984 28
If you need any more details i can give them but i guess i gave the most details. The only thing like i said is only that i don't get any SSID shown on my devices.
here are the Supported interface mode for Wiphy phy1 aswell:
Supported interface modes: * IBSS * managed * AP * P2P-client * P2P-GO * P2P-device
I wanted to repeat the connection from onboard to dongle. but since it won't let me do it and it doesn't show me an AP i can't repeat the wifi connection. what i can't do is that i would go from eth0 to wlan0 because i have no wired connection to repaeat since my rpi is going to be in the staircase. if i would find the driver that is installed for the wifi dongle i have i would try to use that for hostapd but yeah... idk where to find it.