I have run raspi-config and enabled SPI and also verified that /boot/config.txt contains the line:


However, when I run lsmod | grep spi I get the following:

spidev                 16384  0
spi_bcm2835            16384  0

In /dev I can see: spidev0.0 and spidev0.1.

Is SPI enabled and functional? I have a feeling it's not working because my SunFounder LED screen, which relies on SPI, is not working.

2 Answers 2


I have been using raspi-config always found it working. Sometimes my modules are not working. So I usually use two little test programs to check. One program is to repeatedly send out bytes and use a scope to make sure the waveform looks OK. The other test program is a loop back test. I connect MOSI to MISO, send a byte and read back.

You might like to try my test program. It is plug and play, no libraries are required.

I have tested my program with IDLE python. To run in terminal mode:

Don't forget to run with sudo - otherwise the loopback test recvByte returns 0x0. – @glenneroo Apr 24 at 20:49

# spi_test05 tlfong01 2019apr07hkt2043 ***

# Computer = Rpi3B+
# Linux    = $ hostnamectl = raspberrypi Raspbian GNU/Linux 9 (stretch) Linux 4.14.34-v7+ arm 
# Python   = >>> sys.version = 3.5.3 Jan 19 2017

# Test 1   - repeatSendByte() - SPI port repeatedly send out single bytes.  
# Function - Repeat many times sending a byte, pause after each byte.

# Test 2   - loopBackTest()   - SPI port send and receive one byte.
# Function - Send one byte to MSOI and read it back from MISO. 
# Setup    - Connet MOSI pin to MISO pin to form a loop.

from   time import sleep
import spidev

spiPort0 = spidev.SpiDev()
spiPort0.max_speed_hz = 100000

def spiSendRecvOneByte(spiPort, sendByte):
    sendByteArray = [sendByte]
    recvByteArray = spiPort.xfer(sendByteArray)    
    return recvByteArray

def repeatSendOneByte(spiPort, sendByte, pauseTimeBetweenBytes, repeatCount):
    print('\nBegin repeatSendByte(),....')
    for i in range(repeatCount):
        spiSendRecvOneByte(spiPort, sendByte)
    print('End   repeatSendByte().')

def loopBackOneByte(spiPort, sendByte):
    recvByteArray     = spiSendRecvOneByte(spiPort, sendByte)
    recvByte          = recvByteArray[0]

    print('\nBegin testLoopbackOneByte(),....')
    print('      sendByte  = ', hex(sendByte))
    print('      recvByte  = ', hex(recvByte))
    print('End   testLoopbackOneByte(),....')

def testRepeatSendOneByte():
    repeatSendOneByte(spiPort0, 0x5b, 0.0001, 20000000)

def testLoopbackOneByte():
    loopBackOneByte(spiPort0, 0x5b)


''' Smple output tlfong 01 2019apr07hkt2047
Begin testLoopbackOneByte(),....
      sendByte  =  0x5b
      recvByte  =  0x5b
End   testLoopbackOneByte(),....

# *** End ***


Appendix A - SPI Pinouts

rpi spi pinout

  • Don't forget to run with sudo - otherwise the loopback test recvByte returns 0x0.
    – glenneroo
    Commented Apr 24, 2019 at 20:49
  • Ah, many thanks for pointing that. Actually I wrongly assume that the program is always run in IDLE which doesn't need sudo. I should remember to add the remark in the next version that don't to run with sudo if the program is run in text mode.
    – tlfong01
    Commented Apr 29, 2019 at 14:59

SPI is working.

The needed modules are loaded (spidev, spi_bcm2835) and the needed devices are present (dev/spidev0.0 /dev/spidev0.1).

  • "Working" as in recognized by the OS but not necessarily operational. Using @tlfong01's loopback script, receiving data on MISO doesn't work on this Pi but running the script on a different Pi (using the same SD card) works as expected.
    – glenneroo
    Commented Apr 24, 2019 at 17:43
  • @glenneroo Did you read the question "Is SPI enabled?". The answer is yes.
    – joan
    Commented Apr 24, 2019 at 18:02
  • Fair enough, I should have been more accurate framing my question, though my contention stems from the use of the word "working" which in my case is not the case.
    – glenneroo
    Commented Apr 24, 2019 at 18:32
  • 1
    @glenneroo I suggest you test the GPIO. pigpio's gpiotest or wiringPi's pintest. If that passes it sounds like a wiring problem.
    – joan
    Commented Apr 24, 2019 at 18:58
  • 2
    @glenneroo Okay, Connect GPIO 10/9 (pins 19/21). Then enter the following commands. sudo pigpiod then pigs spio 0 50000 0 then pigs spix 0 23 45 67 89 12 13. If the response is 6 23 45 67 89 12 13 then SPI is okay.
    – joan
    Commented Apr 24, 2019 at 20:24

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.