Linked Questions

2
votes
3answers
662 views

Does the DS18B20 1-wire temperature sensor ID change with different Raspberry Pi's?

I have set up 3 temperature sensors (DS18B20) and connected them to what I believe is a Raspberry Pi 4. I have only been using the Pi 4 for easy testing before I move everything over to the Pi zero ...
1
vote
1answer
976 views

Connecting multiple sensors to Raspberry Pi 4 B

I have a Raspberry Pi Project in mind but I'm completely new to this matter and have literally no idea. My plan is to create a transportable Weather Station (which includes a temperature sensor, air ...
3
votes
1answer
260 views

Do most GPIO sketches revolve around processing operating system support (not direct support like arduino)?

I am relatively new to the Raspberry PI platform and more experienced with Arduino. I have noticed in the examples for Infrared Receiving and 1-Wire protocol that the Python sketches to interact with ...
2
votes
1answer
786 views

Rpi3B+ Python DS2482 I2C to 1-Wire Bridge Connecting 10+ DS18B20 Temperature Sensors Using 30 Metres Long CAT5e Cables

I'm about to build a heating control with DS18B20 1Wire-sensors and the Raspberry Pi 3 Model B+. For the 1Wire-interface I'm using the DS2482-800 multi-channel busmaster (more precisely this pre-...
1
vote
3answers
242 views

DS18B20 Temperature Sensor's Power Supply and Rpi's Pull-Down-GPIO-Pin Sinking Current Requirements

I have a RPi zero W and am reading four ds18b20 temperature sensors (with a 10K ohm resistor between the data and vcc line). Now and then I keep getting "SensorNotReadyError" from the sensors. My ...
0
votes
1answer
485 views

Reading analog value Raspberry Pi

I am a newbie with the Raspberry Pi. I want to measure Temperature Reading in 12/16 bit resolution. can someone guide me how CKT should be designed and How can read value using software. usually ...
-1
votes
3answers
126 views

Running RPi 3B without a fan or radiator [duplicate]

I am using my RPi 3B purely for feeding data Flightradar24 (with Pi24 installed instead of pure Raspbian). I assume that usage of electronics and overall load of the device is rather low. My ...
2
votes
1answer
414 views

1-wire device not detected

I'm having trouble getting a 1-wire sensor to be detected on my Raspberry Pi Model 3 B+. The sensor is this temperature and humidity sensor. I have wired the red wire to 3.3V, the black wire to ...
0
votes
0answers
258 views

Rock Pi and temperature sensor

I have Rock Pi 4 B 4GB. Kernel for now is: Linux rock 4.4.154-95-rockchip-gd2ab1f26e1b3 #1 SMP Mon Oct 21 06:42:35 UTC 2019 aarch64 aarch64 aarch64 GNU/Linux I also have DS18B20 temperature sensor ...
1
vote
1answer
156 views

DS18B20 Temperature Sensor RJ-x

I am looking to create a complete temperature humidity sensor system with 72 DS18B20 sensors. I am aware that each sensor receives it's own unique identifier and you are able to daisy chain them ...
1
vote
1answer
131 views

Issue with Pi 4 and 1wire

I've got a Pi 4 and went to hook up a couple sensors, the first being a DHT11, it's working fine. The second being a DS18B20, on the 1-wire interface (using the standard GPIO pin 4). The circuit is ...
3
votes
1answer
59 views

ds18b20 + USB serial adapter

I have this "QinHeng Electronics HL-340 USB-Serial adapter" and a couple of DS18B20 temperature/humidity sensor but I can't get to read data using digitemp. Also tried with this #include <stdio.h&...
2
votes
1answer
90 views

What is the correct hardware required to connect multiple analog sensors to a Raspberry Pi 4?

I've been an avid Bonsai enthusiast for some time, and have always wanted to automate some of the day to day tasks (and get some data logging in the process). I'd like to be able to detect: soil ...
1
vote
0answers
81 views

DS18b20 not detected on Linux raspberrypi 4.19.75-v7

We did following steps: Installed Linux version 4.19.75-v7+ on SD card. Have two DS18B20 connected to the pi (via terminal block). We are using 3v3 ground and GPIO 4.Enabled 1 wire 4.7K Ohm resistor ...
0
votes
1answer
62 views

Choosing the pull-up resistor value for i2c that can cater up to n-number of modular devices

Hello i have designed a modular shield like value that uses the i2c buss of the raspberry but i do not know what resistor value for the pull ups to use. most guides tells us to use a safe 4.7k ...

15 30 50 per page