Linked Questions
20 questions linked to/from What are the Electrical Specifications of GPIO pins?
1
vote
1
answer
905
views
Output/Input Voltage/Curent of RaspberryiPi 3 B [duplicate]
I looked everywhere but i didn't found a good answer.
I'm looking for the specifications of my RaspberryiPi 3 B because i need to connect it with many sensors like LDR sensor or Distance sensor (...
- 11
1
vote
1
answer
738
views
RPi 3 3.3v GPIO normal current [duplicate]
so I've read around forums that the max current from a RPi 3.3v GPIO pin is 50 mA, but since it is the max I don't know if I should take a resistor for 50 mA or for a lower current.
- 61
-1
votes
2
answers
58
views
Can a gpio pin be read as an input without voltage going through? [duplicate]
I have pi 3 and I want to use one of the pin as an input. It will be connected to tapped off wires from a switch that has 2 volts going through it when it is closed. So I want to feed this 2 volts as ...
- 1,025
82
votes
2
answers
119k
views
Raspberry Pi Power Limitations
There are very many, often contradictory, claims about the power requirements and limitations of the Pi.
What are the exact requirements?
- 58.7k
14
votes
3
answers
13k
views
Maximum current on each GPIO pin for Raspberry Pi 3 Model B
Anyone knows what's the maximum input/output current for the individual GPIO pins?
Perfectly fine if someone is able to point me to the Broadcom BCM2837 datasheet, which I for some reason, cannot ...
- 243
4
votes
4
answers
7k
views
Raspberry Pi GPIO input voltage Limit
I am doing a project in which I have a component that outputs a 5 Volt signal.
Since the Pi is only able to handle 3.3 V I connected the signal to a voltage divider.
I used a 4.7 kiloOhm and a 2.2 ...
3
votes
3
answers
2k
views
GPIO input and output levels
I have some basic questions, sorry, I have'nt found this.
What are output levels of GPIO (Raspberry Pi) I mean the voltage
ranges of low and high for input/output
What is the maximum current that ...
- 47
4
votes
1
answer
1k
views
RS232 to Raspberry Pi Zero W
I know this may be a dumb question but can you connect a RS232 Tx, Rx, and Ground from a device directly to the Rx, Tx and Ground on a Raspberry Pi Zero without having to get a Max3232 or something ...
- 71
6
votes
2
answers
3k
views
Electrical characteristics of GPIO
Is there a spec sheet anywhere which lists the electrical specifications for the varios GPIO pins on the RPi revision B? For example, if they are open collector etc, output voltage, max input voltage, ...
- 566
2
votes
1
answer
2k
views
GPIO Voltage tolerance for input
I have not been able to find the input tolerance on I/O pins, especially on the Input pins. If I apply a voltage 3.6v (3.3v +0.3) on an input will it be dangerous or is it ok ?
Does somebody have a ...
- 121
3
votes
2
answers
2k
views
What is the minimum current value into the Pi's GPIO input?
What the minimum current input that must be provided to Pi's GPIO input in order to get high value?
The idea: I will be adding Microwave Doppler which output are in micro amperes. I want to know if ...
2
votes
2
answers
778
views
Do I need a base resistor for a transistor? [closed]
All
I plan to drive a 51 ohm LED using the pi's 5v pin using a 2n2222 transistor connected to the GPIO. Do I need a resistor on the base pin of the transistor or can I connect it directly to a GPIO ...
- 23
1
vote
1
answer
2k
views
Precision of Raspberry Pi GPIO outputs voltages [closed]
Raspberry Pi has several output voltages, GPIO outputs theoretically giving exactly 0V for False and exactly 3.3V for True, 3.3V line and 5V line. However, how precise are these outputs? Can the ...
- 448
1
vote
2
answers
676
views
Lots of LEDs in a chain
I need to control about 90 LEDs with a Raspberry Pi. I am thinking of doing with with 3 chains of 30 LEDs, so I can control each set of 30 LEDs independently (turn 30 on and off at a time) and change ...
- 19
1
vote
1
answer
980
views
Pi GPIO with 1.8 Volt input [duplicate]
Does anyone know will the Raspberry Pi 2 GPIO pins count a 1.8V input as logic one or logic zero?
- 33
2
votes
2
answers
370
views
Short pulse detection about 35ms, is it possible
I got somewhat short pulse 35ms, I written script in python using RPi.GPIO, using event and callback. Is it possible to detect so short pulses? On related question how close to 3V3 I need to get? I ...
- 79
0
votes
3
answers
350
views
How to choose appropriate transistor and resistor values for the 4 digit display?
I bought this 4 digit led display
I'm looking at this tutorial and I don't understand why he used such big resistor for his circuit.
Excerpt:
Please note that the pinouts of LED displays vary ...
- 1
2
votes
2
answers
338
views
Multi-Joystick (Joystick, rotary Encoder, push Button) to GPIOs
I'm trying to connect a Joystick/Encoder/Button (Copal Electronics CJ25) to a Raspberry PI. Using gpiotest I managed to get it up and running pretty well - using 3.3V input (though the data sheet ...
- 33
0
votes
5
answers
298
views
Connecting 5V / 2A DC adapter positive line to GPIO
I have a working DIY UPS for my Raspberry PI 3B board. My requirement is that whenever the main power goes off the PI, the software should be able to detect it and immediately trigger a graceful ...
- 121
0
votes
1
answer
176
views
GPIO only reaches 2,4v when high
TLDR; Under little load the GPIO 22 reaches 3,5v whereas under more load it only reaches ~2,4V, which is not enough to trigger the reset-line on an ATMEGA328P. UART GPIO Pins still reach 3,3V in both ...
