Linked Questions
12 questions linked to/from How can I use an external USB sound-card and set it as default?
36
votes
2
answers
123k
views
USB card as my default Audio Device
I purchased a small USB sound card. My Pi recognizes the device:
$ lsusb
Bus 001 Device 004: ID 0d8c:013c C-Media Electronics, Inc. CM108 Audio Controller
If I run alsamixer and set the audio to USB ...
- 1,160
20
votes
2
answers
34k
views
How do I configure my sound for Jasper on Raspbian Jessie?
I'm using Raspbian Jessie (2015-11-21) to run Jasper (master branch) on the Raspberry Pi 2 Model B.
The installation instructions in the documentation seem to be for Wheezy and not Jessie.
Running ...
- 573
14
votes
3
answers
49k
views
Unable to set default input and output audio device on Raspberry jessie
I am facing a similar problem as described in this question. However I am running Jessie on Raspberry Pi and that it does not have a /etc/modprobe.d/alsa-base.conf file.
So can someone tell me where ...
- 253
2
votes
3
answers
11k
views
No audio output via USB sound card
I bought an external USB sound card for my Raspberry Pi because the sound quality of the built-in 3.5mm audio jack is not that good and I experienced a lot of noise.
The retailer of the sound card is ...
- 21
1
vote
1
answer
5k
views
How to increase mic input volume?
I recently bought a usb soundcard and a 3.5mm microphone for my raspberry pi 4 to use for a python project for speech recognition where I want the pi to be able to hear to conversational volume voices ...
- 11
2
votes
1
answer
4k
views
ALSA input error (snd_pcm_open): No such file or directory - Problem with running Pd with ALSA
I am pretty new to Raspberry Pi, so sorry if I might be not clear on something.
I am trying to set the Raspberry Pi 3 to work running a Pure Data patch while communicating with two Arduino UNO, and ...
- 21
1
vote
1
answer
2k
views
Route Audio Output Through USB Audio Jack
I've an rPi Zero that I want to connect to my speakers to utilise it as an AirPlay receiver via Shairport.
I've made the same setup with my Model B+ and it works great. However, even though I made ...
- 195
1
vote
1
answer
1k
views
How do I get a USB speaker working on a Pi 4 with Raspbian Buster?
I've found several candidate dupes for this - the one that seems to encompass them all (and more) being this one: How can I use an external USB sound-card and set it as default?
But none of them have ...
- 111
1
vote
0
answers
2k
views
Setting USB Sound Card to default device
I have been using raspberry pi 3 model B. And,
I have installed raspbian jessie with pixel.
I made work its camera without an error. I have bought USB sound Card. But, I couldn't make it to work. My /...
2
votes
0
answers
673
views
Error running headless jackd
I'm following the instructions here to run jackd on my headless Raspberry Pi 2 Model B. The only difference is that I'm using the standard packaged jackd instead of the autostatic ones mentioned ...
- 121
1
vote
0
answers
349
views
Getting gstreamer to produce out of usb-audio
I cannot get gstreamer on raspbian (buster) to play through a
usb-audio device, despite other players (vlc, aplay) being able to do
so. but i need gstreamer because of its API access, for mpd players
...
- 111
0
votes
1
answer
39
views
usb sound card no sound with putty
I am trying to configure my USB sound card for use on the pi.
With the graphical interface, I can change the sound card and output the sound to the USB card.
Without the graphical interface with Putty ...
