Questions tagged [board-leds]

For questions pertaining to the onboard LEDs of the Raspberry Pi (PWR, ACT and ETH)

Filter by
Sorted by
Tagged with
0
votes
1answer
118 views

Problem with LED blink program on Pi

I am completely new to RPi and stuck unexpectedly. I am trying to create a simple python program to make my LED blink. Here are the two programs which are giving same outputs on terminal when I ...
3
votes
4answers
139 views

Raspberry pi leds does not blink and the ic gets hot

I bought my raspberry pi 3 model B 4 months back. It was working perfectly but one day, when I was working on pi, all of a sudden, it stopped working. After that day, when I am trying to power it up ...
1
vote
1answer
39 views

Can someone explain what the values are and where they are found?

I'm trying to follow along with this OS building tutorial. I'm trying to understand what the LED_ values in rpi-gpio.h mean and how they are all used. Where in the documentation are these values ...
0
votes
0answers
25 views

Raspberry Pi 3 Model B Hung / Frozen, Including Clock?

I just happened to check on a Raspberry Pi 3 Model B with Raspbian Jessie 4.9.35-v7+ this morning and found it unresponsive. IIRC, there is an LED that is normally on when the Pi is on, so I thought ...
2
votes
0answers
63 views

Control on-board led triggers from python

I know the trigger for on-board leds can be controlled from the command-line (or a script) I have a python program that I want to temporarily take over the system led blink it a little and return ...
1
vote
1answer
164 views

Turn off onboard LEDs at boot

I know very little about Raspberry Pi and Python. I've been able to turn off the LEDs in the terminal using the following command: sudo su - echo none > /sys/class/leds/led0/trigger However, I ...
2
votes
2answers
146 views

Do the Ethernet lights show error codes?

My moel B is flashing all three network lights (FDX, LNK and 100) toghether about once per second. Is this an error message? There is a cable plugged in but there appears to be a break somewhere ...
12
votes
3answers
2k views

How to identify a Pi

I have a stack of five Pis, each of which have a separate hostname and are on the same network. I need to physically identify each Pi from another Pi, perhaps by flashing the onboard LEDs in a ...
2
votes
1answer
838 views

Pi 3 on-board LEDs

Can I make one of the LEDs on the Ethernet port do the same thing as the ACT led? The case I've got my Pi in, does not allow me to see the ACT led so I do not know when its okay to cut the power ...
1
vote
1answer
529 views

Green Led (ACT) is blinking for mmc0 without SD card activity

The green led (ACT) on my Raspberry Pi 3 is set to mmc0 to flash on SD card activity via echo mmc0 |sudo tee /sys/class/leds/led0/trigger However, it flashes much more often (randomly every few ...
0
votes
3answers
159 views

Bad Raspberry boards?

I'm the owner of 5 Raspberry boards. Four of them work flawless. The fifth board regularly refuses to respond to pings or SSH. Sometimes it comes up after a few minutes waiting. It has no firewall ...
5
votes
1answer
10k views

Turning off LEDs on Raspberry Pi 3

I need to disable all LEDs on my Raspberry Pi 3s otherwise they interfere with the operation of my camera setup. I use Raspbian Jessie. I can successfully use the following code: echo 0 >/sys/...
6
votes
4answers
7k views

How can I control the red LED again

I just acquired the latest Pi-3. In the Pi B+ and Pi 2 it was possible to access both the red and green LED through /sys/class/leds/led0 and /sys/class/leds/led1. After setting up the Pi 3, I have ...
4
votes
1answer
3k views

How to read the status of the Power-LED on Raspberry Pi 3 with Python

How to read the status of the Power-LED (or the rainbow square - if you like that better) on Raspberry Pi 3 to detect an low-voltage-condition in a python script? Since the wiring of the Power-LED has ...
1
vote
2answers
970 views

raspberry v3.0, model B read red led status

How can I read the status of the on board red led in raspberry 3.0 model B? Thank you
1
vote
1answer
616 views

Replace ACT- and PWR-Led on Raspberry Pi 3

I somehow broke off the ACT- and the PWR-Leds from my Raspberry Pi 3. It's still working fine, but i want to solder some new ones on. What kind of Led do i need?
0
votes
1answer
125 views

PiGlow script in Python doesn't work

I just bought a PiGlow and a Pibrella, and I was curious how it worked. I imported a few Python scripts from this link, but none of the scripts does work. When I run one of the scripts, I get the ...
1
vote
0answers
76 views

Red light only when plugging Pi2 into AV-Receiver via HDMI, TV works

When I try to plug my Pi2 into my A/V receiver via HDMI and plug in my power cable afterwards, the red light lights up, afterwards the green light lights once and then nothing. When I plug in the ...
0
votes
1answer
400 views

Blinking PWR when not enough current available?

I'm not sure whether I've seen mention of this here before or not. Anyway, I have a B+ with max_usb_current=1 enabled so I can run an external USB drive off it. There's never been a problem with ...