Questions tagged [hat]

A "hat" is an add on board designed specifically to fit on top of the pi via the GPIO header. They have a small EEPROM chip which is used to configure them, but may be built to serve any purpose.

35 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
6
votes
2answers
4k views

Why does the Sense Hat / Astro Pi show the wrong temperature and humidity?

I recently bought the sense-hat, previously called astro-pi. Unfortunately the temperature shows 28 to 31 degrees Celsius from both temperature sensors on the board. They often show around 30 degrees ...
3
votes
1answer
2k views

How to use a GPIO pin after I put on a HAT?

I got a Speaker pHAT for my Pi Zero. According to the pinout, it only uses 5 GPIO pins, so plenty of room to add something else. The problem is, I'm not sure what's the best way to physically attach ...
2
votes
0answers
75 views

Cooling Fan Hat?

The PoE hat has a built-in cooling fan, and even has drivers in Raspbian to automatically turn it on and off based on the CPU temperature. However, any guides to add a temperature-controlled fan seem ...
2
votes
0answers
104 views

No response from RFID HAT

Model: Raspberry Pi 3 Model B Vi.2 HAT: RaspberryPi-B1 v1.3 I just bought RaspberryPi Hat RFID/NFC board (RaspberryPi-B1 from ib technology). I've spent all day trying to get a response from it, but ...
1
vote
1answer
45 views

WaveShare WM8960 Audio Sound Card / HAT Installation on Rpi Zero W Problem

I recently bought the WaveShare WM8960 Audio HAT said compatible with Raspberry Pi Zero W. The install complete without trouble, I can see that the soundcard is installed by typing sudo dkms status ...
1
vote
0answers
18 views

Audio Injector stereo soundcard is preventing boot

I recently bought a Audioinjector stereo soundcard HAT to stream sound on my raspberry pi running Raspbian. I went to their website and installed the .deb installer file and ran it with audioInjector-...
1
vote
0answers
220 views

SIM7600E-H-4G-HAT Raspberry Pi Setup

I am trying to get a SIM7600E-H-4G-HAT running on my Raspberry Pi 3B+, but it is not working. Here is what I've done so far: Inserted my SIM-Card, connected the antenna to Main, connected the entire ...
1
vote
0answers
74 views

Are HATs not supposed to be stackable?

From reading the HAT spec, the ID EEPROM is fixed at address 0x50. This implies that only one real hat may be present at a time, yet lots of products are called HATs and say that they can be stacked, ...
1
vote
2answers
528 views

How to make ups hat run safe shutdown on raspberry when disconnected from the power source

It can be long discussion, because there is no single solution around this, so, to cut the story short, I will tell where I stuck on my way. It is AndroidAuto (media centre in car on raspi) project I'...
1
vote
0answers
84 views

3.5in TFT screen hat and Raspberry Pi 3+b

I'm trying to understand something about the MPI3508 screen I purchased (https://www.amazon.ca/dp/B07DQKQG6X). I tried powering it via usb and connected a PC in its HDMI input and got it working (the ...
1
vote
0answers
64 views

Is it possible to have a correct sound using iQAudio PI-DAC+ and Volumio?

I have bought the excellent Pi-DAC+ to use it with Volumio in an old radio I have. In this radio, the speakers are marked as 6 ohms impedance. This radio used to provide a rather good sound. But with ...
1
vote
0answers
229 views

Has anyone tried connecting a adafruit hat board and an LCD Screen?

We use the Raspberry Pi 3 boards for an elementary school robotics program. We saw these cool Kuman 3.5" touch screens that said they were HDMI (which I assumed meant they connected directly into the ...
1
vote
2answers
996 views

Cirrus Logic Audio card replacement for recording

As is probably well known the Cirrus Logic Audio Card has stopped being manufactured and as such is proving very difficult to get. My reasons for wanting this card was that I needed something with a ...
1
vote
0answers
63 views

Raspberry Pi abruptly “dies” when I apply physical pressure

I have been using my Pi B2 since 2015. I recently got a Sense Hat, but it behaves extremely weirdly when I use it. For example, I used the mini joystick, which applied slight pressure to my Pi. Then,...
1
vote
0answers
251 views

Hat making I2C unusable

I bought this Pi hat for integrating an Arduino with the Pi and exposing all the GPIO pins through nice GVS headers, and overall I'm very happy with it. However, I'm noticing a weird problem. Without ...
1
vote
0answers
208 views

Powering RPi3, 3G Dongle, DC Motor HAT and DC Motors

I've got a setup where I power RPi, 3G dongle from one power source (USB Hub powered from 5V 2A) and a DC Motor HAT and DC Motors (2 small car mirror motors) from a 12V 2A supply. I checked the motors ...
0
votes
0answers
20 views

Are there plans to make a RPI 4 PoE Hat that matches RPI4 power specs?

The RPI 4 draws up to 3amps at 5.1V. The official PoE HAT outputs 2.5 amps at 5V. Generally this should be enough but I'm curious if a higher spec PoE HAT for the RPI 4 is planned? If not can one be ...
0
votes
0answers
23 views

Do the PiJuice and SenseHat HATs clash?

I have two hats a PiJuice UPS and a SenseHat. The GPIO pinouts for each are https://pinout.xyz/pinout/pijuice and https://pinout.xyz/pinout/sense_hat respectively. When I stack my SenseHat onto the ...
0
votes
0answers
25 views

Servo and DC/Stepper Motor Hats Together

I am creating a robot with my Raspberry Pi 3 B+. For my project, I wish to use 2x NEMA 17 stepper motors for moving around, and 2x SG90 servos for managing pan/tilt of the head. I already have an ...
0
votes
0answers
23 views

Distorted sound using VOIP and ReSpeaker HAT

I am using the ResSeaker HAT on my raspberrypi 3. After installing the drivers im able to record the sounds using the inbuilt mic and play it from my speakers (using the command arecord -f cd -Dhw:1 | ...
0
votes
0answers
15 views

respeaker HAT and voip using raspberrypi

I am using the respeaker HAT on my raspberrypi 3. After installing the drivers im able to record the sounds using the inbuilt mic and play it from my speakers (using the command arecord -f cd -Dhw:1 | ...
0
votes
0answers
135 views

Waveshare SIM7600E-H no wwan0 interface when connected to Raspberry Pi 4 model B

I have connected the new Raspberry Pi 4 model b with the waveshare SIM7600E-H 4G HAT. The os is Raspbian Buster Lite. The configuration I use is the following: 1) The jumpers are placed in the middle ...
0
votes
0answers
35 views

Are there any battery backup options that work with a PoE powered Pi?

Looking to have a Pi (4) that is powered over PoE - are there any battery backup options (i.e. hats) that can be stacked with the PoE hat & supply power if/when the PoE fails (and then re-charge ...
0
votes
1answer
32 views

Is my ClusterHat faulty or my RPi GPIO fried?

I've been using a ClusterHat (1RPi + 4 PiZeroes) and all has been well until recently. The PiZeros boot off the RPi's SD card using the ClusterHAT-2018-10-09-lite-1-usbboot boot image, and when I ...
0
votes
0answers
103 views

Unable to get accurate RPM with Adafruit Stepper Motor HAT v0.1

I'm trying to drive some stepper motors using a Raspberry Pi 3 B V1.2 and an Adafruit Stepper Motor HAT v0.1 and am having trouble setting them to the speed I want. The motors have a step angle of 1.8 ...
0
votes
0answers
29 views

Analog input together with LoRaWAN

I am looking for a hardware configuration enabling me to read an analog input from ammeter and collect the historical data and send them over LoRa to a server. So I could use something like Monarco ...
0
votes
1answer
315 views

Problem with HAT GSM/GPRS/GNSS/Bluetooth

I have: Connected rasspbery pi zero with HAT GSM/GPRS/GNSS/Bluetooth by gold-pins. List item Switched UART to B-position Raspbian version: 9 (stretch) When I used pwdrkey i have only PWR and STA ...
0
votes
0answers
117 views

How to turn multiple servos by an angle using the Adafruit servo/pwm pi hat?

So I'm using a Raspberry Pi Model 3b and an Adafruit 12-bit PWM Servo/PWM Pi Hat on my project to control 6 independent continuous servos. I'd like to send in signals that would turn the servo by that ...
0
votes
0answers
87 views

ADC Hat with 8 differential channels and 24 bit resolution for 100 - 200 SPS (Hz)

I'm sorry if there's a similar post, I could not find it (them). As the title implies, I'm looking for an ADC hat for the Rapspberry Pi 3 Model B with 8 differential channels to sample up to 200 SPS (...
0
votes
0answers
192 views

Pimoroni Speaker Phat i2c and using the pins

Is it possible to use the pins on top of a raspberry pi hat that uses i2c? I am trying to use the Pimoroni Speaker Phat and control a motor using GPIO at the same time. Thanks for any replies.
0
votes
1answer
183 views

Finding EEPROMS suitable for HATs

I'm working through the HAT design guide to work out what kind of EEPROMs I can use. To quote it: 24Cxx type 3.3V I2C EEPROM must be used (some types are 5V only, do not use these). The EEPROM must ...
0
votes
2answers
296 views

sense hat sample “snake” returns “event device not found” error

My "sense hat" sits ontop of a raspberry pi 3. I've completed the installation instructions found at https://www.raspberrypi.org/documentation/hardware/sense-hat/ lexu:~> sudo apt-get update lexu:~...
0
votes
1answer
82 views

Can I use a DHT22 sensor with the servo hat installed on my RPi-3?

the title pretty much says it all... My son an I are doing some robotics experimenting with the RPi-2 and RPi-3, we are using the Servo Hat to control several servos on them. We would like to ...
-1
votes
1answer
295 views

Disabling Hat EEPROM scan

How do I free the Hat EEPROM I2C bus (bus 0?) on a + model? I ask because the primary bus is blocked by an TFT I'm using, and I want to solder nothing to the Pi GPIO.
-3
votes
0answers
34 views

Can a Pi Zero be stacked on top of the GPIO pins of a regular Pi?

I'm curious if anybody has attempted to use the bare board Pi Zero (without the GPIO pins pre-soldered) as a virtual Pi on a Pi HAT for a full size Raspberry Pi (2, 3 or 4, etc)? I see the possibility ...