Stack Exchange Network

Stack Exchange network consists of 175 Q&A communities including Stack Overflow, the largest, most trusted online community for developers to learn, share their knowledge, and build their careers.

Visit Stack Exchange

Questions tagged [ipv6]

Use this tag for any discussion relating to the IPv6 addressing system. This can include 4to6 conversion, or devices that do or do not support IPv6 addressing.

3
votes
2answers
149 views

Cannot connect to my Pi over SSH from IPv4 to IPv6

I am trying to set my Raspberry Pi as a server at home using IPv6. At home I have a dual stack. I need to know how can I connect from outside internet IPv4 (Client) to IPv6(Server at home) via SSH. ...
1
vote
1answer
56 views

Ping 'Realm local all Thread nodes' multicast

I'm using rpi3 with raspbian to set up an OpenThread Borderrouter. For my application, I need to ping the 'Realm local all thread nodes' multicast address. Unfortunately, I get an error when doing ...
1
vote
1answer
199 views

Connecting to Pi from Windows via Zeroconf - IPv4 pings fine, IPv6 does not

I've been struggling with getting into my Pi from Windows 10. I'm fairly sure the problem is on the Pi side but if so I can't for the life of me work it out. In short, on Windows I cannot ssh or ping ...
1
vote
0answers
52 views

How to setup 6rd?

How to setup 6rd on a Raspberry Pi? The ISP router doesn't have the option of it enabled and the other router I have doesn't really work behind NAT (just using it as an access point right now). I've ...
0
votes
0answers
154 views

IPv4 not working after losing connection to router

When I restart my router I can't connect to my Pi(3) anymore via IPv4 (IPv6 works!) until I restart the Pi (I've tried connection with SSH, SFTP, DHCP, HTTP(S) and the ping command). It is connected ...
2
votes
1answer
535 views

Raspberry can only reach IPv6 sites

I have a Raspberry Pi 3 Model B (with Raspbian Stretch Lite installed) connected to my laptop by Ethernet using a static IP address (network: 192.168.128.0). I can access it through ssh without any ...
1
vote
0answers
177 views

Setup Windows 10 IoT with Hurricane Electric's IPv6 Tunnel

I just bought a Raspberry Pi 3 and I'd like to install Windows 10 IoT on it as I'm a Microsoft fan. I've been using a Pi B as an IPv6 tunnel machine with Tunnelbroker.net but have been using Raspian. ...
1
vote
3answers
1k views

SSH over ipv4 to ipv6

At home I have a ipv6 modem, my ISP provides only ipv6. My RPi is connected to modem/router over ethernet and gets ipv6 address. I can reach it (ssh) locally from my windows laptop using ipv6 global ...
2
votes
1answer
113 views

IPv6 DAD Failures on RPi3

I tried configuring IPv6 over the included WiFi interface on a Raspberry PI v3 using the latest Raspbian/Jessie. Unfortunately, this fails because I get DAD (duplicate address detection) failures. ...
3
votes
2answers
130 views

Access camera via IP6 router on rpi3

I have set up a motion camera in rpi3 running jessie. When I tried to access it from local network it works fine i.e. http://localIP:8081 The issue now is that I'm trying to access it from outside. ...
2
votes
1answer
376 views

ipv6 stopped working, how can I fix it?

I have tried: modprobe ipv6 Which returns modprobe: ERROR: ../libkmod/libkmod.c:557 kmod_search_moddep() could not open moddep file '/lib/modules/4.4.21-v7+/modules.dep.bin' It has worked until ...
2
votes
1answer
2k views

Does appending ipv6 to /etc/modules enable IPv6 at boot?

Apparently, I can enable IPv6 in two ways. To test, I first confirm it's not enabled currently. $ ping6 -c 1 ::1 socket: Address family not supported by protocol I then enable it immediately $ sudo ...
-1
votes
1answer
96 views

PuTTY can't launch X programs when IPv6 is disabled

I'm accessing my Raspberry Pi 3 with PuTTY, and using X11 programs like GParted through ssh connection. It was perfectly working until I turned off IPv6 by adding the following line to /etc/sysctl....
1
vote
1answer
701 views

Why doesn't IPv6 over SLIP work?

The goal I'm attempting to connect two Raspberry Pi's together using IPv6 over SLIP but it's not quite working. Here's what I've done: The attempt Both Pis are Model B running Jessie and the same ...
2
votes
4answers
7k views

How to find out my Raspberry Pi IPv6 address in local area network?

My Raspberry Pi runs ArchLinux and since I enabled IPv6 in our local router config, the pi only fires up an IPv6 connection in LAN. But I have trouble to find out the address. Once I connected a ...
2
votes
1answer
260 views

dchpcd[PID]: eth0: {IPV6} is unreachable, expiring it

I have a small python script that uses Requests and simply does a GET request from an api to pull data. This script works fine on my computer and fine on a pi A, but not on the actual Pi B that I'm ...
1
vote
1answer
5k views

How to check ipv6?

So, I'm building hadoop cluster with raspberry right now, I need to disable ipv6 connectivity, and need to know whether ipv6 has been disabled or not. In some guide cat /proc/sys/net/ipv6/conf/all/...
33
votes
5answers
7k views

IPv6 connectivity

Is IPv6 connectivity supported on the Raspberry Pi? If yes, is it enabled by default/how do I turn it on?