The Stack Overflow podcast is back! Listen to an interview with our new CEO.

Questions tagged [ppp]

PPP (Point-to-Point Protocol) is a data transfer protocol. Quite often it is used in relation to the Pi for transferring data to the Pi over a Serial Cable. Use this tag if your question involves PPP such as problems with setting up, transferring files, controlling connections, etc.

12 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
1
vote
1answer
206 views

set ppp0 as default gateway permanently

I have a Zero W with a 4G module, to use the sim to access internet I did: pi@raspberrypi:~ $ ip route default via 10.111.100.1 dev wlan0 proto dhcp src 10.111.100.143 metric 302 10.64.64.64 dev ...
1
vote
0answers
68 views

How to use AT over uart and ppp0 over ttyS0 at same time

I have a cellular data card that connects through ttyS0. I can talk to it via Putty using AT commands, or from Python using /dev/ttyS0. When I enable a ppp0 interface over ttyS0 to communicate with ...
1
vote
1answer
2k views

How to enable on-demand cellular PPP connection as backup to eth0

I have a Raspberry Pi 3 device to which I have added a MultiTech MTQ-LAT3-B02 modem. I am able to successfully use pppd to connect to the cellular network. I then can add a ppp0 route and ...
1
vote
0answers
93 views

PPTP client is broken after update

I am using Raspberry Pi 1 B+. Unfortunately, the new Raspberries that I bought recently (2017) don't boot anymore with my custom-made image. Only my Raspberries 1 B+ from 2014 accept to boot, so I ...
1
vote
0answers
476 views

Establish PPP via serial cable

I am trying to enable PPP via USB serial cable from my laptop to my rpi. As per http://elinux.org/RPi_Serial_Connection, I have entered the following on my laptop: sudo pppd noauth proxyarp /dev/...
0
votes
0answers
30 views

How to start PPPD connection on boot and handle it in case of network failures?

I have to setup Quectel EC25-E hooked up to my Rasp Pi Zero. I can setup the ppp connection but manually. This is what I do: Quectel module ppp connection However, I have to make this pi headless ...
0
votes
0answers
23 views

How to use Raspberry Pi3 to make two GSM or GPRS modems in order to create a PPP link

Good day. I need to connect two VHF high band repeaters via GSM or GPRS modems using Raspberry Pi3, in order to create a PPP link. There was a UHF link before, but due to theft from the one site, we ...
0
votes
0answers
110 views

RaspberryPi as PPPoE server - issue in starting ppp service

All, I am trying to configure my RaspberryPi 3 B as PPPoE server (wlan 0 as wan and eth0 as lan). The below mentioned link is used to configure the PPPoE server and all the mentioned config provided ...
0
votes
0answers
69 views

Unable to access internet in PC when connected to Pi(ppp0) via Ethernet

I am using openhabian. I have managed to get the Pi connected to the internet via the Quectel UC20-G modem after which I get a new interface called ppp0 with IP address 49.225.37.106 as shown below. ...
0
votes
1answer
268 views

Connect to the raspberry over SSH via mobile connection

I finally got it working that I can use a Huawei E173 modem on my raspberry. When activating it with sudo ifup 3gModem everything works fine, and it connects itself to my Server as I can see it ...
0
votes
1answer
370 views

Alternating ppp0 and ppp1 interfaces

I was hoping I could use some expert help on my ppp interfaces. My setup is as follows. I have a Rpi 3 Model B that has two ppp connections (one 2G sim900 module and one 3G huawei dongle). My system ...
0
votes
1answer
3k views

how connect my Pi to Internet through PPPoE connection?

i'm new to pi. I need to connect my raspi, for the first time to internet. As the PC i need to establish an pppoe link to my router as required from my internet service provider. I don't know what'...