Questions tagged [rfid]

RFID stands for "radio-frequency identification" and is used to identify and track objects via wireless communication over short distances.

Filter by
Sorted by
Tagged with
0
votes
2answers
5k views

how to enable spi1? / pi 3 and two rc522 RFID readers

Is it possible to connect two RC522 readers with one RaspberryPi 3? As far as I know I should just choose different CS pins for them (Add more than 2 SPI slaves). I have following connections: 1st ...
4
votes
1answer
8k views

Major trouble with nRF24L01+ controllers and the RF24 library

I've had a hellish last three days. All I've wanted to do is get an Arduino Uno and a Raspberry Pi B+ talking to eachother with these little guys, and after following many different tutorials, I've ...
1
vote
0answers
3k views

RFID RC522 Stops reading data after reading data continuously

I'm trying to make RFID RC522 work with my Raspberry Pi 3 B+. I use the library MFRC522, and the the sensor can read data most of the times. However if I just put the card on the sensor it will stop ...
1
vote
2answers
9k views

ITEAD PN532 on Pi 3 with libnfc

For the past weeks I have been trying to get the ITEAD PN532 NFC board working on a Raspberry Pi 3 running Raspbian Jessie (2016-03-18) using libnfc. Here's some info on the board itself. It has two ...
6
votes
2answers
2k views

Impossible to scan RFID tags using libnfc, PN532, and RPi3

I recently bought this NFC/RFID reader PN532 module V3 I want to use it with my raspberry pi 3. I have install and configured the library libnfc. The PN532 is connected with I2C. I have well enabled ...
5
votes
1answer
8k views

Raspberry Pi and the ACS ACR1252U USB NFC Card reader

I'm using a ACS ACR1252U card reader (http://www.acs.com.hk/en/products/342/acr1252u-usb-nfc-reader-iii-nfc-forum-certified-reader/) connected via USB and to be honest I have no idea how to get it ...
1
vote
2answers
674 views

How to read Wiegand serial data? (Rx/Tx)

Ok, I am losing my mind... Why is this so damn difficult? Current situation: - 12V Access control device that is connected like this i.e. Wiegand D0 to Tx and D1 to Rx, with voltage dividers. - ...
1
vote
2answers
3k views

MFRC522 Not working over SPI Interface

I am running (on a Pi3) an MFRRC522 reader - much like this one: It has been working fine, but after I changed SD card, to increase capacity - whilst also doing a new Raspian install I haven't been ...
1
vote
0answers
911 views

Connect two SPI RFID readers in the Raspberry Pi B +

I followed this tutorial to connect one RC522 RFID reader in a Raspberry Pi. http://www.nikolaus-lueneburg.de/2014/06/rfid-rc522-modul-mit-spi-schnittstelle/ I'm able to connect it to work with ...
1
vote
1answer
28 views

RC522 modules stop working when more than 2 are connected

So, here's a synopsis of what I am trying to do. I want to put 3 RC522 readers side by side inside of a book, facing the cover, that will be constantly on, using a Rpi zero W. When an RFID chip gets ...
0
votes
3answers
4k views

how to use two rfid rc522 nfc tag reader with a raspberry pi?

I am currently using a rfid rc522 nfc tag reader with raspberry pi using the MFRC522-python code. In my project I need to collect data from two rfid rc522 cards at the same time, rc522 are located at ...