Questions tagged [usb-hub]
An USB hub is a device that expands a single USB port into multiple ports, thus allowing to connect more devices to a host system. The USB&LAN controller (LAN9512) acts as on on-board USB hub on the Raspberry Pi (except Pi Zero).
117
questions
0
votes
0
answers
18
views
Set PiZero's startup usb mode
I have a USB expansion hat connected and if I plug in a usb kbd and mouse receiver into the hat and pi is connected via power usb everything works as expected - mou and kbd control the pi and no ...
- 1
0
votes
0
answers
54
views
USB HUB gets disconnected
I have Pi Zero 2 W with an USB dongle. This dongle connects an external Wifi antenna and a mic to the Pi.
The problem is that the USB dongle gets disconnected after 5-30 minutes. Then I have to ...
- 1
0
votes
0
answers
51
views
Can't power RP4 from same active hub the peripherals are connected to
I'm building something NAS-like with a RPI4 Model B Rev 1.2 and 2 hard disks. I'm using an active hub for the hard disks and wanted to power the RPI4 from it as well. Here is how I wanted to wire it:
...
- 1
0
votes
0
answers
17
views
I have a raspberry pi3 and i want to use the ethernet port on my pi to send ethernet connection to my laptop
Is it possible to use my raspberry pi3 like a USB ethernet adapter to send ethernet through to my laptop using a USB, I dont care if the network isn't crazy fast I just want to play games on my laptop
- 1
0
votes
0
answers
137
views
Pi 4B OTG USB advanced troubleshooting/debug or logs
I followed this wonderful guide:
https://magpi.raspberrypi.com/articles/pi-zero-w-smart-usb-flash-drive
and I was able to made it working on my loved Pi4B.
Everything works fine as mass storage ...
0
votes
0
answers
49
views
Raspberry pi zero 2w and usb c hub
I have a raspi zero 2w and inside flirc case and using 4year old 16gb sd card and headless pi os; it uses usb micro to usb c and then usb c to ethernet.
I wanted to transfer some files from pi to my ...
- 101
1
vote
1
answer
164
views
UDev rule for removing device not triggered
I am having a monitor with an integrated USB hub (and a physical power-switch) attached to my pi and want to execute two different scripts, when the monitor is turned on and off.
The first part for ...
- 111
1
vote
2
answers
380
views
Can I power a raspberry Pi 4B from a connected powered USB 3 Hub with 2 USB 3 hdd's connected?
I'm currently running a first gen. model B as a SMB media server with two 2.5 inch USB 3.0 disks connected to an externally powered USB 2.0 hub connected to the Pi. The Pi itself is also powered with ...
1
vote
0
answers
235
views
Using Raspberry Pi as USB device description pass-through/emulator
TLDR: Is it possible to use a Pi (or Pi like device) as a method for emulating a USB device descriptor and passing packets across?
If I could get the Pi to emulate the correct ID and details, I could ...
1
vote
0
answers
150
views
how to give power and ETH to pi pico W at same time?
Learning following project https://github.com/sbcshop/Raspberry-Pi-Pico-RFID-Expansion.
Now the requirement is to connect project with Ethernet network, also provide power supply at same time.
Qustion:...
- 109
0
votes
1
answer
395
views
I broke SSH access to my Raspberry Pi
I had my Raspberry Pi 3B+ running old Raspbian Jessy. I was connecting to it by ssh. I have installed uhubctl.
uhubctl is a tool which can turn off power supply for USB port.
I got
# uhubctl
Current ...
- 175
1
vote
2
answers
570
views
Pi 4 won't boot after powered USB hub was connected
MY Pi 4 won't boot anymore after I connected a Sabrent HB-UMP3 powered USB Hub. The Pi4 had been running just fine for around 2 years, yesterday I hotplugged the abovementioned hub and the Pi ...
- 111
3
votes
4
answers
3k
views
Raspberry pi-4 powered usb hub backfeed issues
I have a Raspberry SC15184 Pi 4 server and I'm looking to power 3 USB peripherals each with a 3-6W power requirement (which should be 0.6-1.2A given pi-4 operates at ~5V).
This is above the 1.2A ...
- 131
1
vote
1
answer
812
views
How many HDDs can be connected to a raspberry pi zero 2w (by using usb hubs)?
Trying to find out how many drives I can connect to a raspberry pi 2w. Basically how many devices the host controller supports.
More information: this is a for a Chia (crypto) harvester. I would be ...
- 111
1
vote
2
answers
781
views
Using a PD USB hub for power and data for Pi 4
I want to use a 7" LCD (not the official Pi 7" LCD) together with the Pi 4. According to the LCD documentation, it requires 2A. I was planning initially to power the LCD through one Pi.
Now ...
2
votes
1
answer
390
views
Use powered USB hub for peripherals and power
I want to run an external HDD on a Pi (currently a first-generation model, I might replace it with a Pi 3 in the future). The drive has no extra power supply apart from its USB port.
Just plugging the ...
- 217
0
votes
0
answers
18
views
Raspberry PI4 usb 3.0 seems not working properly [duplicate]
I am using a Raspberry PI4 with Google Coral TPU and a Telit Lte modem both attached on USB 3.0 ports. I get a lot of "Under-Voltage" messages also using the Raspberry power supply(5.1V, 3A)...
0
votes
0
answers
603
views
raspberrypi kernel: [14247.511414] mmc0: timeout waiting for hardware interrupt
Setup = Rpi > USB HUB > USB TTL adapter/cable > 2 LTE modules.
Protocol = AT Commands.
Problem = mmc0: timeout waiting for hardware interrupt.
Question = Any investigation method and ...
0
votes
0
answers
522
views
Would it be possible to emulate a ps4 controller on USB-out
Would it be possible to create a PlayStation 4 controller USB interceptor of sorts for the purpose of using macros? The project’s model would look like this:
• You are plugging PS4 controller in one ...
1
vote
0
answers
670
views
Problem with booting Raspberry Pi 400 from USB drives
Summary:
I have a USB3 flash drive that I can use to boot my Raspberry Pi 400 without a problem, but only when it is directly attached to one of my my RPI 400 USB3 ports.
However, when I attach the ...
- 111
-1
votes
1
answer
419
views
Can I use the usb pins on the pi cm4 directly?
I'm designing my own CM4 breakout board. If I only need one usb device, can I use the usb pins on the pi cm4 directly without the multiplexer chips?
- 59
0
votes
0
answers
584
views
Connect Raspberry Pi from Android App through USB
I'm building an android app where there's a requirement to show the temperature in the app from the sensor in Raspberry Pi Controller. For this purpose, I'm trying to connect my android device to ...
- 101
0
votes
1
answer
83
views
share ethernet connexion to ethernet usb adaptor thanks to raspberry pi
I try to connect my ps4 with my vpn connexion without using the computer. I install the vpn on a raspberry pi 2 and i connect my raspberry to internet by the ethernet connexion. I use the raspberry ...
- 11
1
vote
0
answers
59
views
Connecting hub to 1 USB port vs 2 USB ports?
The Pi 4B has 2x USB 3.0 ports. I have 2 choices to connect my hard drives:
Using a single 10-port hub which connects to 1 USB 3.0 port.
Using two 5-port hubs which connect to two USB 3.0 ports.
...
- 111
0
votes
1
answer
251
views
External HDD causes SSD to not boot, but works fine when plugged in later
I have a Raspberry Pi 3 model B with no microSD card (the OTP bit is set). It can boot from an SSD connected via a USB2 SATA adapter. However, when a 3½-inch USB3 HDD is connected, the Pi doesn't boot....
- 103
0
votes
0
answers
285
views
RPi4 USB-C hub not working on reboot
I have a LogiLink USB-C 3-Port Hub UA0315 plugged in Raspberry Pi 4 which is powered through external power supply. The hub is working when plugged in, however on reboot it is no longer detected until ...
- 1
0
votes
2
answers
2k
views
Usb not working on RPI4B [closed]
Keyboard and mouse and hub not working. I have acess via SSH and VNC though my laptop. The pi cannot see all that. I tried lsusb but nothing shows up except
Bus 002 Device 001: ID 1d6b:0003 Linux ...
- 19
1
vote
0
answers
423
views
Raspberry Pi 2B External HDD not detected
I'm trying to connect my external hard drive to my Raspberry Pi 2B, but I am not able to get it to show up. I am running the latest Raspbian, and I have updated my software. Running lsblk --fs, I only ...
- 11
1
vote
1
answer
2k
views
Is it possible for a Raspberry Pi Zero to act as both a Usb Gadget and a Usb Host?
I am currently working on a Raspberry Pi project, and found an amazing feature that I used many times on my LineageOs phone: Usb Gadget.
I figured I could change the function of the Usb port to act as ...
- 138
0
votes
1
answer
3k
views
Disable USB driver on RPi Zero W
I am using a Raspberry Pi Zero W running Raspberry Pi OS (32-bit) Lite (Aug 2020).
This is an IoT project where, I have a USB modem that makes my internet connection. When the modem is powered on it ...
- 27
-1
votes
1
answer
190
views
It's possible to power Raspberry Pi Zero though a USB Hub?
I want to use a Raspberry Pi with 2 USB connections. One connecting it to a computer and one connecting it to another device. This is possible, right? I just need to use a USB hub.
But can I power up ...
- 1
0
votes
1
answer
612
views
Setting USB current limit on Raspberry Pi 4
I have a Samsung Galaxy s8 that's connected to my Raspberry Pi in order to provide an internet connection. I'm looking to limit the harm done to the battery in the phone.
Right now the battery in the ...
- 1
2
votes
2
answers
755
views
Raspberry doesn't recognize me disconnecting a USB device
I have a Raspberry Pi with an Amazonbasics 10-port USB hub which has a PPPS (port per port switching) function, basically, it can turn off power to any power via a tool called uhubctl.
When I use ...
- 21
1
vote
0
answers
1k
views
How can Rpi4B use multiple on board and USB based UART / serial ports?
there. I am trying to use rpi 4 to access my own device through UART. However, the number of UART port isn't enough for me since I'm trying to access more device in same time. Thus, I want to know if ...
- 21
1
vote
0
answers
519
views
How many usb devices does raspberry support? [duplicate]
Colleagues, hello, everyone. I have a raspberry that produces errors, 10 usb devices connected to it via hub. What's the diagnosis?
I have the following equipment installed:raspberry pi4 model B 4 GB,...
- 21
1
vote
1
answer
2k
views
Error when connecting more than ten USB devices on Raspberry Pi 4 [duplicate]
What is the limit of USB devices in raspberry pi4?
We have an external USB hub with its power supply and 10 devices fall off with errors.
[Wed Mar 11 09:04:43 2020] usb 1-1.3.4-port1: Cannot enable. ...
- 21
1
vote
0
answers
195
views
USB ports for 4G modules disappears after resetting the 4G module
I am using the EC25 quectel LTE module with Raspberry Pi 3 Model B. I can access the internet using serial pins of raspberry pi i.e. UART Tx and Rx. I can find ttyUSB[0-5] in ls \dev. I am sending AT ...
- 269
1
vote
0
answers
1k
views
Getting ftdi_sio ttyUSB0: failed to get modem status: -32
Iam using Raspberry pi 3b along with Xbee and Sixfab 3G/4G base sheild. getting
ftdi_sio ttyUSB0: failed to get modem status: -32
usb usb1-port1: disabled by hub (EMI?), re-enabling...
and also ...
- 11
3
votes
2
answers
2k
views
Using USB hub to power external hard drive
My Raspberry Pi can't produce enough power for WD external drive. I see that people recommend using a USB hub.
My WD hard drive has only one input. If I connect it to a USB hub, how do I connect the ...
- 131
1
vote
1
answer
81
views
Powered USB Hub Requirements
I dont plan on powering my Pi through a USB hub, but I do intend on hooking up some HDD's to a powered hub since everything I see so far seems to indicate that the pi cant power multiple HDD's.
If ...
- 31
-1
votes
1
answer
2k
views
The USB ports do not work anymore on my RPI4
Since yesterday, the USB ports of my RPI4 do not work.
When I plug a usb device like a hard drive or a usb stick, I don't see any message about it in the logs and no new device in /dev.
When I type ...
- 1
0
votes
1
answer
164
views
Signal generator connected to raspberry pi via USB
Ido connect to the device from my raspberry pi and able to send commands. The power consumption of the SG is 2.5 W. That means that the current of usb port should be 2.5 / 5 = 500 mA.
>>> ...
- 11
1
vote
1
answer
237
views
Will this work out (usb hub + rpi zero w + Zishan Z1 DSD)?
Well, I want to connect Rpi zero W and Zishan Z1/2 DSD in one case, but with both devices working in one port connected to PC. (with working usb device in Rpi if in "portable" mode or in both ...
- 33
17
votes
7
answers
58k
views
Best way to power multiple Raspberry Pi 4s?
I ordered a few Raspberry Pi 4s, still under way, each with their own power supply, and I plan to get more, but when I have been previously able to power RPis with USB-hub, there's apparently no USB-C-...
- 179
4
votes
2
answers
162
views
Powered USB3 Hub vs USB3 Y Power Cable
I have an issue that means I have to use a powered USB hub for the HDD that is attached to my RPI4 (long story). The hub just broke.
My budget doesn't allow for a decent powered USB3 hub BUT does ...
- 193
8
votes
10
answers
11k
views
RPI4 won't boot with powered USB hub
I have an RPI4 running a Plex server, Pihole, etc etc.
Power kept dropping while running certain tasks involving the attached HDD, so I started using a powered USB3 hub - problem solved.
But now the ...
- 193
0
votes
0
answers
26
views
Can I issue a command when a specific message issued in the syslog
I am having power problems with my USB devices which is proving difficult to resolve. However I can see on the syslog that there is a specific error message which shows there is a problem. What I ...
- 1
0
votes
1
answer
412
views
LTE modules connected to USB hub cannot be accessed
The USB-HUB is self-powered, and two LTE modules are connected via USB-SERIAL to USB-HUB.
We are facing a problem is that,The devices which are connected to USB-HUB can not be accessed. Is there any ...
1
vote
2
answers
142
views
USB hub raspberryPi
I've been searching for a host-powered USB hubs with Raspberry Pi and discovered that most of the hubs are sort of built for the raspberry Pi device.
I intend on using the USb port for serial ...
3
votes
1
answer
522
views
Read/Write LAN9512 EEPROM
We are building a device around the Compute Module 3 and since it needs internet access we decided to go with the LAN9512 that was also used in the Raspberry Pi earlier.
The LAN9512 requires an ...
- 143