**No router + regular Ethernet cable + RPI 2 Raspbian 2018-11-13 Lite + Ubuntu 18.10**
Before inserting the SD card on the Pi, remove and re-insert it on the host to remount it, and then create magic empty file named `ssh` file in the `boot/` partition.
On Ubuntu hosts, it gets mounted automatically at:
/media/$USER/boot
so you can do:
sudo touch /media/$USER/boot/ssh
but you can confirm it with:
lsblk
which creates:
mmcblk0 179:0 0 14.4G 0 disk
├─mmcblk0p1 179:1 0 43.9M 0 part /media/ciro/boot
└─mmcblk0p2 179:2 0 14.4G 0 part /media/ciro/rootfs
This is needed to enable the SSHD daemon on the Pi as explained at: https://raspberrypi.stackexchange.com/questions/58478/ssh-not-working-with-fresh-install otherwise `ssh` fails with:
ssh: connect to host 10.42.0.160 port 22: Connection refused
Then, boot the Pi, and link an Ethernet cable from your laptop directly to the Pi:
[![enter image description here][1]][1]
On Ubuntu 17.04 to work around [this bug](https://bugs.launchpad.net/ubuntu/+source/network-manager/+bug/1678606) as mentioned [on this answer](https://raspberrypi.stackexchange.com/questions/67594/unbuntu-17-04-direct-shared-ethernet-connection-fails-with-active-connection-co/72211#72211) you first need:
sudo apt-get install dnsmasq-base
On the host, open the network manager:
nm-connection-editor
And go:
1. `+` sign (Add a new connection)
1. Ethernet
1. Create
1. IPv4 Settings
1. Method: Shared to other computers
1. Set a good name for it
1. Save
[![enter image description here][2]][2]
Find the IP of the Pi on host:
cat /var/lib/misc/dnsmasq.leases
outputs something like:
1532204957 b8:27:eb:0c:1f:69 10.42.0.160 raspberrypi 01:b8:27:eb:0c:1f:69
`10.42.0.160` is the IP, then as usual:
ssh [email protected]
I also have the following in my `.bashrc`:
piip() ( cat /var/lib/misc/dnsmasq.leases | cut -d ' ' -f 3; )
pissh() ( sshpass -p raspberry ssh "pi@$(piip)"; )
From inside the Pi, notice that it can access the internet normally through your host's other interfaces:
ping google.com
For example on my laptop, the Pi takes up the Ethernet, but the host is also connected to the internet through WiFi.
The crossover cable is *not* required if the host network card supports [Auto MDI-X](https://en.wikipedia.org/wiki/Medium-dependent_interface#Auto_MDI-X). This is the case for most recent hardware, including for example the 2012 Lenovo T430 I tested with, [which has](https://support.lenovo.com/gb/en/documents/pd024705) an "Intel® 82579LM Gigabit Network Connection" which [documents support for Auto MDI-X](http://www.intel.com/content/dam/doc/datasheet/82579-gbe-phy-datasheet-vol-2-1.pdf).
Now you can also:
- access the Internet from the PI through your Ubuntu's Wifi connection
- open a VNC to get rid of the display as well: https://raspberrypi.stackexchange.com/questions/14611/how-to-set-up-raspberry-pi-without-a-monitor/54393#54393
**UART serial USB converter**
This is an alternative to SSH if you just want to get a shell on the Pi: https://en.wikipedia.org/wiki/Serial_port
This does not use SSH or networking itself, but rather the older, simpler, more direct, more reliable, lower bandwidth, lower distance serial interface. The Pi won't have access to the Internet with this method.
Desktop computers still have a serial port which you can connect directly wire to wire with the Pi, but these are hidden in most laptops, and so we need to buy a cheap USB adapter. Here I've used: https://www.amazon.co.uk/gp/product/B072K3Z3TL See also: https://unix.stackexchange.com/questions/307390/what-is-the-difference-between-ttys0-ttyusb0-and-ttyama0-in-linux/367882#367882
First plug the SD card on the host, and edit the `config.txt` file present in the first partition to add:
enable_uart=1
as explained at: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=141195
This first partition contains the bootloader, its configuration files and the (Linux / your) kernel, `config.txt` being one of them. The second partition contains the actual Linux root filesystem.
Now connect your computer to the Pi as:
[![enter image description here][13]][13]
You only need to attach 3 cables:
- Ground to Ground
- Tx on Pi to Rx on the USB to serial port
- Rx on Pi to Tx on tye USB to serial port
This is also documented at: https://www.raspberrypi.org/documentation/usage/gpio/README.md
Be careful not to link the Ground to the 5V, I've already burned 2 UART to USB chips by doing that!
You don't need to connect the 5V to the 5V at all. I think you can power your Pi like that, but I've read that this is a bad idea, just use the usual USB power source.
Finally, plug the USB side of the connector to your host computer, and get a shell with:
sudo apt install screen
sudo usermod -a -G dialout $USER
screen /dev/ttyUSB0 115200
Exit with `Ctrl-A \`.
Here is a video by Adafruit showing it: https://www.youtube.com/watch?v=zUBPeoLW16Q
[1]: https://i.sstatic.net/8C0mJ.jpg
[2]: https://i.sstatic.net/ZU18R.png
[13]: https://i.sstatic.net/L0XyU.jpg