340
votes
Accepted
How do I set up networking/WiFi/static IP address on Raspbian/Raspberry Pi OS?
This tutorial describes how to setup networking using the default network manager dhcpcd included in Raspbian since 2015-05-05 and Raspberry Pi OS.
It applies to the Foundation releases of Raspberry ...
- 58.2k
107
votes
How do I set up networking/WiFi/static IP address on Raspbian/Raspberry Pi OS?
This tutorial describes how to setup networking using the default network manager dhcpcd included in Raspbian since 2015-05-05 and Raspberry Pi OS.
It applies to the Foundation releases of Raspberry ...
- 58.2k
41
votes
How do I set up networking/WiFi/static IP address on Raspbian/Raspberry Pi OS?
For a static IP address on an Ethernet connection:
sudo nano /etc/dhcpcd.conf
Type in the following lines on the top of the file:
interface eth0
static ip_address=192.168.1.XX/24
static routers=192....
- 429
25
votes
Fix error "Failed to start DHCP Client Daemon" after upgrade to "Bullseye" remote?
There is a fix for this "Failed to start DHCP Client Daemon" on Updated to Bullseye, needed to change my dhcpcd.conf reddit thread for anyone that has the same problem with Failed to start ...
- 251
14
votes
How do I set up networking/WiFi/static IP address on Raspbian/Raspberry Pi OS?
Short and foolproof method how to do this with:
Raspbian Jessie, Stretch, Buster
This will set a fixed IP and enable the ssh daemon:
Stick the sd card in your pc and find that it has two ...
- 593
13
votes
Accepted
Fix error "Failed to start DHCP Client Daemon" after upgrade to "Bullseye" remote?
This occurs following dist-upgrade to bullseye and prevents the Pi from getting network access.
Further to the answer from @Ivan (which fixed this problem for me), you can make the necessary change to ...
- 278
8
votes
"connection problem, giving up" on xrdp with Raspberry Pi OS 11 (bullseye)
I tested 32bit and 64bit for Pi Zero, 3 and 4 then I found that the problem happens only on 4.
The OS I tested are released on 2021.01.28.
Pi type
OS
RDP login status
Zero
32bit
No problem
3
32bit
...
- 181
7
votes
Accepted
What is the RaspberryPi OS equivelant of "http://packages.ubuntu.com/"?
If you are actually using RpiOS, the URLs are in /etc/sources/sources.[list,list.d]. However, redirection is often used and you won't find everything in one place, so your best bet is to observe what'...
- 58.3k
5
votes
Accepted
"connection problem, giving up" on xrdp with Raspberry Pi OS 11 (bullseye)
Turns out you cannot login twice with the same account using xrdp on Raspbian Bullseye (Debian 11). So you need to either disable autologin using "Raspberry Pi Configuration"/sudo raspi-...
- 198
5
votes
Accepted
What are the pros and cons of the new Raspberry Pi OS Bullseye?
This version seems to have been designed for users who use the GUI Desktop on a Pi4/Pi400 with little consideration for those running older models, headless or at CLI (and even less testing of these ...
- 58.2k
5
votes
Accepted
SSH Login Not Working
On my other device I run ssh ucyt5040@localhost
localhost is the network address of the machine you are using.
You need to give the network address (by name or IP address) of the Raspberry Pi running ...
- 70.4k
4
votes
"connection problem, giving up" on xrdp with Raspberry Pi OS 11 (bullseye)
The reason is not only the autologin. Even if autologin is disabled for the user pi, you will not be able to login via RDP with this user under Bullseye.
I created an own user, and at first I could ...
- 41
4
votes
How do I set up networking/WiFi/static IP address on Raspbian/Raspberry Pi OS?
First thing you should do is make your Raspberry pi's IP static. So that whenever you power up your Raspberry pi it should connect to your access point(Hotspot).
Connect to your Access point. Type ...
- 217
4
votes
What is up with the different repositories and URLs?
Presumably you have installed Raspberry Pi OS 64bit on the newer Pi.
This uses the standard Debian ARM64 repository not the Raspbian.
The firmware is still provided by Raspberry Pi Ltd. and the source ...
- 58.2k
3
votes
Fix error "Failed to start DHCP Client Daemon" after upgrade to "Bullseye" remote?
(Before doing this process, BACK UP THE CARD!!!!! Copy it's contents onto another sd card. If something wrong happens, the result could be TERRIBLE!)
To reset the password, You need to put the os sd ...
3
votes
connman unable to connect to wifi: No carrier
I would just delete connman - from similar posts the dhcpcd plugin (I would have to search to find its name) appears to be installed.
Its normal operation depends on the dhcpcd service (which appears ...
- 58.2k
3
votes
How do I set up networking/WiFi/static IP address on Raspbian/Raspberry Pi OS?
SystemdNetworkd
Raspbian/Raspberry Pi OS initially used Debian Networking which was replaced by dhcpcd in 2015.
dhcpcd is the current default networking system.
Raspbian is now based on systemd which ...
- 58.2k
3
votes
Screen resultion when using VNC / headless
Add ",nocomposite" to the dtoverlay line in config.txt and then you will get the headless resolution options show up in raspi-config. As detailed here by HawaiianPi.
- 31
3
votes
Accepted
Enable console auto-login via commandline (ansible script)
As mentioned by @SteveRobillard, raspi-config can be used in noninteractive mode. The functionality is, however, not documented. The functions have to be checked in the source code https://github.com/...
- 161
3
votes
Accepted
Where are the cube2 sauerbratren runtime binaries located?
Looking at the package details it looks like they are likely to be found in a subdirectory of /usr/share/games/sauerbraten.
You can verify this using the which command:
which "command name"
...
- 34.5k
3
votes
Accepted
What to do if FUSE has no option NOFAIL in Raspian Bullseye 64bit?
I read about this issue here: https://github.com/libfuse/libfuse/issues/691
So there seems to be libfuse 2.9.9 in Debian Bullseye: https://packages.debian.org/bullseye/fuse
The entry for Buster looks ...
- 309
3
votes
Accepted
i2cdetect shows addresses starting from 8
Try i2cdetect -a -y 1
default range is from 0x08 to 0x77
NOTE man i2cdetect will show this (and other options)
- 58.2k
2
votes
rfkill disables my Wifi and Bluetooth since the Bullseye upgrade. How to disable it permanently?
Bullseye is not yet released, even though the packages have been already pushed to the repo on 14.08. It's expected that not everything will work right away.
Note that you should have used apt-get ...
- 27.6k
2
votes
Accepted
How to disable the dynamic IP address after assigning a static IP in Bullseye?
Update: a better solution: uninstall connman
Based on the Q&A and comments in connman unable to connect to wifi: No carrier it looks like the installation of connman was an unintended consequence ...
- 474
2
votes
"connection problem, giving up" on xrdp with Raspberry Pi OS 11 (bullseye)
I'm on an Rpi 4 running the latest 64 bit OS (as at April 2022). I have been searching for a way to get this working and tried all the different combinations including creating a new user account (...
- 21
2
votes
Debian Bullseye Compatible Raspberry Pi OS
No one can answer your question - it is unanswerable, just as the question, "When will the universe collapse on itself?" You've asked for an opinion, not an answer. That said, it seems ...
- 20.7k
2
votes
Bluetooth disconnects when SSH connection closes (RPi Zero 2)
If someone stumbles upon this: pulseaudio was the culprit. pulseaudio uses systemd to check if anyone is logged on, else it shuts down. This also closes the BT connection.
I fixed my problem by ...
- 161
2
votes
Accepted
No internet connection post-buster to bullseye upgrade
If you followed the advice to perform a fresh installation you would have no problem (at least with networking - there are other issues with Bullseye).
There are others reporting the same issue (which ...
- 58.2k
2
votes
No internet connection post-buster to bullseye upgrade
I had the same problem, and sudo apt purge connman fixed it after the fact.
However losing your network connection while doing a remote upgrade causes a lot of trouble. I have not tested it, but in ...
- 121
2
votes
Accepted
Only top scored, non community-wiki answers of a minimum length are eligible