Darkest N2O
  • Member for 4 years, 2 months
  • Last seen more than 3 years ago
How to automount a USB drive
1 votes

First create a new folder in /mnt . It needs to be called usb. Next, make a new file with leafpad and type inside it: sudo mount /dev/sda1 /mnt/usb -o uid=pi,gid=pi Save it as Mount.sh on desktop. ...

View answer
Can't SSH into Pi
1 votes

How I did a headless setup on a Mac. Downloaded etcher. Downloaded zip file of raspbian (you are using Ubuntu, not sure if it will work this way) Plugged in my SD card and burned the zip file to the ...

View answer
Raspberry Pi 3 states connected to the WiFi but not visible on access point (pi cannot be pinged either)
0 votes

What does the wifi bar at the top say? Have you tried forgetting password then re entering Restarting router

View answer
Playing audio via bluetooth speaker for Pi3 (Stretch)
0 votes

This usually happens with me. It's basically trial and error. First off, you need to turn off Bluetooth (if you have it on). Then turn on the Bluetooth speaker, and turn on Bluetooth on the RPi. At ...

View answer
Raspberry Pi 2 Won't Boot
0 votes

SD card needs to be formatted as FAT32 Use Etcher if you aren't already doing so. Download Raspbian Desktop ZIP file from Raspberry Pi Foundations Download website Don't open ZIP file. Burn to SD card ...

View answer
HDMI not recognizing Pi 3 on first boot
Accepted answer
0 votes

This regularly happens if you dont place the HDMI cable in before booting up. You just have to unplug the pi, insert HDMI, then boot up again.

View answer
Bluetooth problem
0 votes

Found out how to fix it: switch off bluetooth on pi turn on bluetooth on headphones to make it discoverable turn on bluetooth on pi and connect to headphones Thats it! watch your vids/music.

View answer
Raspberry doesn't boot on second time
0 votes

My raspberry pi 2 had a problem sort of like this. I used an 8GB kingston card. I think that you should either and rewrite the image to it or buy a new SD card that is used in car cameras. These ...

View answer
How to boot without mounting a Drive present during booting
Accepted answer
0 votes

Thanks for all the help. I found out a way. All you have to do is DONT EDIT the /etc/fstab folder, make a new text editor file, and write mount -a (location point). Then save it as mount.sh and put it ...

View answer
Empty desktop after typing "startx"
0 votes

I accidently did this before as well. I had used the lite version of raspbian rather than the full version with desktop mode. As you said you have a 2GB micro SD card, I would personally think it ...

View answer
Cannot get WiFi to work on PI 3 running stretch
0 votes

Is the image a desktop image? If so connect your Pi to your router and find the IP address of it on the routers webpage. Then ssh into it. Enable VNC in raspi-config. Download tight vnc onto your ...

View answer
How do I make a copy of a NOOBS SD card?
0 votes

Very simple way. All you have to do, is download the noobs software from the raspberry pi foundations website, unzip it open the noobs file then copy everything there (not the noobs file the stuff ...

View answer
Can't always access my Raspberry Pi through PuTTY (SSH)
0 votes

Plug the raspberry pi into your router with an Ethernet cable. Fire the pi up and the lights on the Ethernet module should start blinking. Then goto your routers webpage and insert you username and ...

View answer
Powerbank and Pi overheating?
Accepted answer
0 votes

The power bank shoudn't get hot. The raspberry pis core is a pretty small square. As you said there is no ventilation. If possible, place the power bank on top of the older box and feed the cable into ...

View answer
RPi-2 : Red led flashes after few seconds
0 votes

Used a higher Amp USB socket, and works fine now.

View answer
How come my Raspberry Pi doesn't show total storage?
0 votes

As above @mintyfreshpenguin said that to see all storage on your raspberry pi, do df -h.

View answer
Sharing exFAT drive via Netatalk, can't create directories
0 votes

In your macbook terminal do: cd (drive name) than try mk (directory name) If it doesnt work try using sudo before the command.

View answer
copying files to raspberry pi from usb flash
Accepted answer
0 votes

Try using cd (your usb drive name) than do sudo mv (source) (destination) if this doesnt work, check if your usb drive is read and write, not only read. Hoped this help you!

View answer
Connection error
0 votes

This is how i did a headless setup on my mac (should work on other conputers also) Downloaded etcher and latest raspbian desktop image 2.inserted sd card, burned zip file with etcher to it. etcher ...

View answer
How long will powered by 2400 mAh powerbank work?
-1 votes

Here is a calculator to save the math work: https://spellfoundry.com/raspberry-pi-battery-runtime-calculator/

View answer
How to connect and use ssh without a screen using BUILDROOT
-1 votes

This is how i did a headless pi setup: downloaded etcher and latest raspbian software from raspberrypi.org Used etcher to burn the file to my sd card etcher automatically ejects the sd card, place it ...

View answer