Skip to main content

My hard drive is a 3.0 1TB seagate with wifi.Wi-Fi (NTFS) It. It needs 5V and 2A.

The pi
My device is a Pi2 B RaspbianRaspberry Pi 2 B running Raspbian.

I created a Y-Split UsbUSB 3.0 cable. One end is going to the Drive  (obviously) There is one end going to a wall charger  (the one that came with the hard drive) ---> ONLY THE GROUND AND POSITIVE WIRES ARE ATTACHED.ONLY THE GROUND AND POSITIVE WIRES ARE ATTACHED.

The other end goes to the raspberry piRPi where the Ground and Positive wires are completely disconnected since I am getting power from somewhere else.(But the data wires are all still connected.

I tested it inon my windowsWindows desktop and my windowsWindows laptop and the drive works perfectly fine.

I have nstf-3gnstf-3g installed on the pi. The drive has always been used with windows machines previously. When I type sudo blkid, the drive does not show up.

I tried googling for this issue for a while now.. Every forum says it is because the Hard drive is not getting enough power and to connect the drive to a usbUSB hub. But my drive is getting full power from the wall outlet.

I amI'm starting to wonder if the problem could be: since the positive and ground wires were completely disconnected from the usbUSB cable's end going to the piPi, the piPi somehow does not know there is a drive connected there? I find it weird that it works on my windows machines then?...

If you need anymore information let me know.

My hard drive is a 3.0 1TB seagate with wifi.(NTFS) It needs 5V and 2A.

The pi is a Pi2 B Raspbian

I created a Y-Split Usb 3.0 cable. One end is going to the Drive(obviously) There is one end going to a wall charger(the one that came with the hard drive) ---> ONLY THE GROUND AND POSITIVE WIRES ARE ATTACHED.

The other end goes to the raspberry pi where the Ground and Positive wires are completely disconnected since I am getting power from somewhere else.(But the data wires are all still connected.

I tested it in my windows desktop and my windows laptop and the drive works perfectly fine.

I have nstf-3g installed on the pi. The drive has always been used with windows machines previously. When I type sudo blkid, the drive does not show up.

I tried googling for this issue for a while now.. Every forum says it is because the Hard drive is not getting enough power and to connect the drive to a usb hub. But my drive is getting full power from the wall outlet.

I am starting to wonder if the problem could be: since the positive and ground wires were completely disconnected from the usb cable's end going to the pi, the pi somehow does not know there is a drive connected there? I find it weird that it works on my windows machines then?...

If you need anymore information let me know.

My hard drive is a 3.0 1TB seagate with Wi-Fi (NTFS). It needs 5V and 2A.
My device is Raspberry Pi 2 B running Raspbian.

I created a Y-Split USB 3.0 cable. One end is going to the Drive  (obviously) There is one end going to a wall charger  (the one that came with the hard drive) ---> ONLY THE GROUND AND POSITIVE WIRES ARE ATTACHED.

The other end goes to the RPi where the Ground and Positive wires are completely disconnected since I am getting power from somewhere else.(But the data wires are all still connected.

I tested it on my Windows desktop and my Windows laptop and the drive works perfectly fine.

I have nstf-3g installed on the pi. The drive has always been used with windows machines previously. When I type sudo blkid, the drive does not show up.

I tried googling for this issue for a while now.. Every forum says it is because the Hard drive is not getting enough power and to connect the drive to a USB hub. But my drive is getting full power from the wall outlet.

I'm starting to wonder if the problem could be: since the positive and ground wires were completely disconnected from the USB cable's end going to the Pi, the Pi somehow does not know there is a drive connected there? I find it weird that it works on my windows machines then?...

If you need anymore information let me know.

Source Link

Raspberry pi 2 not detecting my Seagate External Hard Drive

My hard drive is a 3.0 1TB seagate with wifi.(NTFS) It needs 5V and 2A.

The pi is a Pi2 B Raspbian

I created a Y-Split Usb 3.0 cable. One end is going to the Drive(obviously) There is one end going to a wall charger(the one that came with the hard drive) ---> ONLY THE GROUND AND POSITIVE WIRES ARE ATTACHED.

The other end goes to the raspberry pi where the Ground and Positive wires are completely disconnected since I am getting power from somewhere else.(But the data wires are all still connected.

I tested it in my windows desktop and my windows laptop and the drive works perfectly fine.

I have nstf-3g installed on the pi. The drive has always been used with windows machines previously. When I type sudo blkid, the drive does not show up.

I tried googling for this issue for a while now.. Every forum says it is because the Hard drive is not getting enough power and to connect the drive to a usb hub. But my drive is getting full power from the wall outlet.

I am starting to wonder if the problem could be: since the positive and ground wires were completely disconnected from the usb cable's end going to the pi, the pi somehow does not know there is a drive connected there? I find it weird that it works on my windows machines then?...

If you need anymore information let me know.